Jump to product information
1 from 10
12 reviews

Battery Adapter for Rolleiflex SLX, 6006 (USB-C Rechargeable)

Battery Adapter for Rolleiflex SLX, 6006 (USB-C Rechargeable)

Three Li-ion cells with USB-C replace the old original battery in your Rolleiflex SLX or 6006.

Regular price €219.95
Regular price Sale €219.95
incl. VAT · free shipping Currently not shipping to the USA: With 3 rechargeable batteries (ships within Germany only) / Wavy (same look as the 6006); With 3 rechargeable batteries (ships within Germany only) / Smooth (same look as the SLX, 6001, 6002, 6003). Why?Currently not shipping to Canada: With 3 rechargeable batteries (ships within Germany only) / Wavy (same look as the 6006); With 3 rechargeable batteries (ships within Germany only) / Smooth (same look as the SLX, 6001, 6002, 6003). Why?🟢 In stock · 26,000+ customers

Three Li-ion cells with USB-C replace the old original battery in your Rolleiflex SLX or 6006.

Fits:

Rolleiflex SLX, 6001, 6002, 6003, 6006. Not for the 6008 series, not tested with the 6001 RCC. See all models

What’s in the box
Surface

Free shipping within Germany

Free shipping, delivered to your door in 2-4 business days.

Find out more here.

30-day money-back guarantee free returns in Germany

You can try out any product for 30 days. If you’re not happy with it, we’ll refund the full purchase price, including shipping costs. No ifs, no buts.

Find out more here.

  • High-current board with gold-plated contacts: passes short current peaks cleanly, so the fuse doesn’t mistake them for a sustained load. This also gives sluggish cameras some headroom, but it’s no substitute for a service.
  • Snap-latch swap: sits firmly in the battery compartment and swaps out without tools.

You’ll also need: For the cage without batteries, 3 Nitecore NL1411R batteries (14500, USB-C). For charging, a USB power adapter with a USB-A socket for the charging splitter. Because of the regulations for lithium-ion batteries, we only ship the set with batteries within Germany.

Safety instructions

Important: Never charge the batteries in the camera’s original charger. Only use the USB-C ports on the cells.

All safety information

  • The fuse is not pre-installed. The wrong fuse can damage the camera.
  • The cage has no BMS of its own. All protection against overcharging, deep discharge and overheating comes solely from each cell’s own BMS. Unprotected cells can overheat, catch fire or explode, so only use protected 14500 cells with their own BMS. We accept no liability for damage caused by unprotected cells.
  • No 1.2 V or 1.5 V AA cells (NiMH, alkaline or “1.5 V USB-C”): the voltage is too low. Only genuine 3.6 / 3.7 V 14500 Li-ion cells.
  • Do not open, short-circuit or crush the cells, or heat them above 60 °C. Store them dry, and dispose of damaged or swollen cells immediately.

Compatibility

The v2 battery adapter is designed for the Rolleiflex 6000 series. Which of the three fuses goes in your camera depends on the model:

Fuse Compatible cameras
0.8A (slow-blow) Rolleiflex SLX
Rolleiflex 6006
Rolleiflex 6002
1.0A (slow-blow) Rolleiflex 6006 Multi Exposure (also known as 6006 model 2)
Rolleiflex 6003 SRC 1000
1.25A (slow-blow) Rolleiflex 6001
Rolleiflex 6001 Professional
Rolleiflex 6003
Rolleiflex 6003 Professional

Not suitable for the 6008 series (6008, 6008 Professional, 6008 Professional SRC 1000, 6008 i, 6008 i2, 6008 E, 6008 AF, 6008 Integral, 6008 Integral 2). The 6008 models draw such heavy current spikes that the protection circuits in the batteries cut out even with fully charged cells, so this version won’t run reliably on them. A new version for the 6008 is in the works, and you’ll hear about it through the waiting list for the 6008 adapter. If you own a 6008 and have received this adapter, please get in touch.

Not tested by us: Rolleiflex 6001 RCC. Its electronics read the voltage of the NiCd battery and have had trouble detecting lithium-ion cells in the past; we can’t guarantee that the new board solves this. Please write to us first: we’ll talk through the chances of success, and if it doesn’t work out, we’ll take the adapter back as a goodwill gesture.

Limits with rapid-fire shooting: On a 6006 in continuous mode at 1/500 s, the battery protection briefly cut out from about half charge onwards, and on cameras with stiff mechanics this can happen sooner. So it’s best to recharge early.

Our battery list shows more Rollei models that take the RFX6000 battery and the complete RFX6000 camera list.

Choose your finish: smooth or ribbed

Both finishes are technically identical; only the look differs. The outside of the cage becomes part of the left side of your Rollei’s body.

  • Ribbed: fine grooves like those on the 6006.
  • Smooth: sits flush like the original battery of the SLX, 6001, 6002 and 6003.

Not sure? Send us a photo of the left side of your camera body.

What's included

Item With 3 batteries (ships within Germany only) Without batteries (ships worldwide)
1× Battery cage v2 with high-current board (gold-plated contacts) ✓ ✓
3× Nitecore 14500 1100mAh lithium-ion batteries (USB-C port, status LED, 3 A continuous current) ✓ –
1× USB charging splitter (charges all batteries at the same time) ✓ ✓
1× fuse set in a storage box: 0.8A, 1.0A, 1.25A (slow-blow glass fuses, IEC 60127) ✓ ✓
1× quick start guide (DE/EN) ✓ ✓

Other 14500 batteries with USB-C and at least 3 A continuous current will work too from a technical point of view, but we haven’t tested them. Retailers stocking the NL1411R in Germany, the EU, the UK and the US are listed in the “Shipping and buying internationally” section of our guide.

Technical details

  • Cage material: engineering plastic
  • Circuit board: high-current board v2 with gold-plated contacts
  • Battery cells (set with batteries): 3× Nitecore NL1411R 14500 lithium-ion, 3.6V nominal, 1100mAh, 3 A continuous discharge, 7 A short-term surge
  • Energy per pack: approx. 12 Wh (complies with UN3481 Section II)
  • Charging port: USB-C directly on each cell, built-in protection circuit
  • Fuses: set of 0.8A / 1.0A / 1.25A (slow-blow glass fuse, IEC 60127), storage box
  • Colour: black
  • SKU: 1758

Description

When fully charged, the three cells briefly deliver 12.6 V, slightly more than the 9.6 V of the old NiCd pack. We’ve tested the adapter extensively and consider the electronics of the 6000 series designed to handle this. Still, with an unserviced camera more than 30 years old, a fault can never be completely ruled out. We accept no liability for damage to the camera or its electronics; the 30-day money-back guarantee applies to the adapter. For more on the voltage (Rollei’s own Power Interface was specified for 12 to 18 V), our battery comparison and what causes electronics failures, see our guide to the Rolleiflex 6000 battery problem.

Installation

  1. Fitting the fuse: Use the table under “Compatibility” to pick the right one of the 3 included fuses, then fit it yourself.
  2. Charging the batteries: Always outside the cage, with all 3 cells together on the USB charging splitter, each through its own USB-C port; the status LED shows whether a cell is charging or full. Always charge and insert the three as a fixed set, and only once all of them are full: a cell with less charge will be the first to run flat, and the camera then gets sluggish or stops, even though the others still have charge left. Once the pauses between shots start getting long, stop and recharge all three.
  3. Inserting the cells: Place the 3 cells in the cage following the plus and minus markings. Each cell must sit fully in its slot, with none sticking out at the side. The snap latch clicks audibly into place.
  4. Into the camera: Slide the cage into the battery compartment just like the original battery until it’s properly seated. If it jams, don’t push any further: if forced, it may be very hard to get out again. Pull it out, check that all cells sit fully in their slots, and send us a photo if it still jams after that.

Frequently asked questions

“What should I do if the camera doesn’t respond or stops after a few shots?”

  • Are all three cells full? Charge them together until every status LED shows a full charge. Even from around half charge, the camera may cut out at fast shutter speeds and only fire again after you switch it off and on.
  • Is the right fuse fitted (see the table under “Compatibility”), and is its wire still unbroken?
  • Are the contacts clean, both on the cage and in the battery compartment?

If the camera still won’t run after that, the problem may lie with the camera itself, for example ageing capacitors or gummed-up mechanics. In that case, drop us a line with your camera model and the fuse you’ve fitted, and we’ll work with you to track down the cause.

“What should I do if the fuse blows when shooting in Continuous mode?”

If the correct fuse blows during continuous shooting, that almost always points to hardened grease inside the camera: the drive, mirror and shutter then draw considerably more current than the factory intended. Our recommendation: plan a service (CLA) with a specialist workshop such as Wiese Fototechnik. They will also check the ageing capacitors on the camera’s circuit board, which are the most common real cause of failure in the 6000 series.

Check the fitted fuse first. If you previously had a lower rating in there, its wire may have broken long ago. That looks like a power problem, but it’s just a blown fuse. Hold it up to the light: if the wire is unbroken, it’s fine.

As a temporary fix at your own risk, you can use the next higher fuse rating (e.g. 1.0A instead of 0.8A on an SLX). This slightly lowers the level of protection: if a fault occurs, the fuse blows later, which in the worst case can damage the camera’s circuit board. Acceptable until your service appointment, but not recommended long term.

Download the instructions as PDF (German and English)

Show full details

Customer reviews

4.6 out of 5

Based on 12 reviews100% verified reviews

Transparency: Every customer who reviews an item bought from us receives a discount code for their next order, regardless of the star rating.

  1. Peter T.Verified purchase

    Perfect fit, 100% functional

    Great how this battery holder replaces the original one. Very good service and involvment of the Ausgeknipst people.
    First it did not work, even if the batteries were fully loaded. Replacement of the batteries solved everything.
    Chapeau für Ausgeknipst. Go on whith the good work!

  2. Paul S.Verified

    Batterieadapter für Rolleiflex 6006

    Passt perfekt und wurde schnell geliefert

  3. Johannes G.Verified

    Neuer Akku ohne Aufwand.

    An meiner SLX (1. Baureihe) funktioniert der Akkusatz von "Ausgeknipst" einwandfrei - sowohl im Einzel- als auch im Serienbetrieb. Auch der 3D-gedruckte Akku-Dummy schnappt wunderbar in das Gehäuse und verriegelt zuverlässig. Das Laden der Akkus über den USB-Verteiler ist etwas gewöhnungsbedürftig, funktioniert aber einwandfrei. Beim Einsetzen in den Batteriekorb auf richtige Polung und guten Kontakt achten!

  4. ChristophVerified

    Batterie Ersatzakku für Rolleiflex 6000

    Passt perfekt und ist damit sicher verankert am Kameragehäuse. Technisch funktioniert alles bestens. Schön das es nun eine zeitgemäße Energieversorgung für die Rollei gibt. Akkus lassen sich problemlos nach längerer Zeit Auswechseln wenn sie keine Leistung mehr bringen sollten.

  5. peter S.Verified

    battery adaptor for Rollei 6006

    received the battery adaptor in perfect order.
    Fits nicely in the camera and works fine.
    Very happy with the purchase. My old Ni-cad battery was getting old and needed constant charging.
    So pleased I bought the one from Ausgeknipst as I now can use my 6006 for a long time to come
    Peter in Brisbane

  6. KKVerified

    Ordinary high drain type li-ion like vapcell h10 cannot provide sufficient power to drive Rolleiflex 6008AF as the voltage drop too much under heavy loading. LiFepo4 type 14500 battery (pulse current at least 2A and 3.5A is better) can drive manual focus lens on 6008AF but not AF lens.If you can offer a battery adapter that can accomodate four 14500 LiFepo4 batteries, it is very likely that the AF lens can be operated on 6008AF

  7. YuriVerified

    Batterieadapter für Rolleiflex SLX, 6006, 6008 (USB-C Akku)

    Gutes Netzteil, von den angebotenen - das Beste! Eine leichte Einstellung des Riegels bereitet keine Probleme. Sehr zufrieden!

  8. Michele C.Verified

    Good item and good after sales support

    A well-made item that works perfectly. The price might be a little high, but it gets the camera working perfectly again. Fast and efficient customer service.

  9. BorisVerified

    Akku für Rolleiflex 6000er System

    Aufgrund der Herstellungsweise im 3D-Druck ist dieser Batteriehalter nicht besonders passgenau. Zuerst ließ er sich nicht einsetzen und es floss auch kein Strom. Aber nach mehrere Male einsetzen und wieder herausnehmen passte es dann. Läuft jetzt einwandfrei. Das Teil ist die technisch beste Lösung. Sind die Akkus dann doch irgendwann am Ende, dann kann man die auch ohne Werkzeug austauschen.

  10. Valeriu S.Verified

    is made of regular plastic an is not easy to take it off tha camera but all and all is working Good

    the adapter for filer for lens is cheap plastic.I was expecting for metal but works

Transparency: Every customer who reviews an item bought from us receives a discount code for their next order, regardless of the star rating. “Verified purchase” means the review came through the review link of an order in our shop. How we collect and check reviews

We're Anto & Vladi

Support a young startup

Looking for innovative solutions instead of mass-produced gear? With us, you’re not buying from an anonymous wholesaler but directly from the founders. We (Anto & Vladi) started our business in Würzburg in October 2021 to help you bring film photography back to life.

Ausgeknipst Print Room - 3D Drucker Produktionsstaette

Designed by engineers

Engineered in Würzburg

We don’t sell anything we wouldn’t use ourselves. We’re engineers and camera nerds, and we know that precision matters, especially with camera gear. That’s why we design our parts ourselves in Würzburg, and we make and assemble most of them here too. Batteries and rechargeables are bought in from suppliers such as Varta.

Ausgeknipst Versand und Lager - Gelbe Lagerkisten

From Germany to anywhere in the world

Fast DHL shipping

Don’t want to wait forever for your part? We pack every order in Würzburg and ship it on the next shipping day (Monday, Wednesday or Friday). Within Germany, it then reaches you in 2-4 days with DHL or Deutsche Post.