Zu Produktinformationen springen
1 von 11
2 Bewertungen

Copy Stand für Analog Digitalisierung und Scan

Copy Stand für Analog Digitalisierung und Scan

Hält deine Digitalkamera stabil und parallel über dem Film, wenn du Negative abfotografierst.

Normaler Preis 249,95 €
Normaler Preis Sale 249,95 €
inkl. MwSt. · versandkostenfrei 🟢 Auf Lager · 26.000+ Kunden

Hält deine Digitalkamera stabil und parallel über dem Film, wenn du Negative abfotografierst.

Art

Kostenloser Versand in DE

Mit kostenlosem Versand in 2-4 Werktagen bei dir zu Hause.

Hier erfährst du mehr.

30 Tage Geld-zurück-Garantie kostenlose Rücksendung in DE

Du kannst jedes Produkt 30 Tage lang testen. Solltest du nicht zufrieden sein, erstatten wir dir den vollen Kaufpreis inkl. Versandkosten. Ohne wenn und aber.

Hier erfährst du mehr.

  • Kamera direkt montierbar: Du schraubst sie auf die 1/4"-Schraube der Nivellierbasis, die bei jeder Variante dabei ist, und richtest sie gleich dort aus.
  • Feinjustage in jede Richtung: Die Nivellierbasis neigt deine Kamera um bis zu 15°, dreht sie um 360° und zeigt dir an der Libelle, wann sie waagerecht steht.
  • Hält auch schwere Kameras inklusive Makro und Balgen: Bis 3 kg für Kamera und Objektiv zusammen haben wir getestet, das reicht auch für digitales Mittelformat.
  • Hoch genug für alle Formate: Von Kleinbild bis 4×5 Großformat, je nach Sensor und Makro. Gerechnet sind je nach Aufbau bis rund 62 cm zwischen Film und Sensor, an Vollformat genug für 4×5 mit einem 90-mm-Makro.
  • In 5 Minuten einsatzbereit: Die Säule kommt fertig montiert, du schraubst sie mit zwei Schrauben an die Grundplatte und setzt die Nivellierbasis auf. Werkzeug und Aufbauanleitung auf Deutsch und Englisch liegen bei.

Du brauchst zusätzlich:

So arbeitest du mit dem Copy Stand

Höhe einstellen

Halte den Schlitten fest, löse den Klemmhebel und schieb die Kamera auf die Höhe, die dein Filmformat braucht. Dann ziehst du den Hebel wieder fest.

Ein paar Millimeter nachstellen

Für die letzten Millimeter legst du den Daumen in die Mulde am Schlitten und schiebst in kleinen Schritten.

Kamera ausrichten

Mit der Nivellierbasis gleichst du aus, dass sich jeder Reproständer unter dem Gewicht von Kamera und Objektiv minimal durchbiegt.

Mit dem Justierspiegel prüfen

Der Justierspiegel liegt dort, wo sonst der Film liegt. Du stellst die Basis so ein, dass die Spiegelung deines Objektivs im Live View genau in der Bildmitte steht, dann steht die Kamera parallel zum Film.

Kamera wechseln

Zum Abnehmen der Kamera öffnest du die Basis. Zum Aufsetzen setzt du die Kamera wieder auf und schraubst das Oberteil der Basis zu.

12 kg am Schlitten

Kompatibilität

  • Kamera: über die 1/4"-Schraube der Nivellierbasis, passt auf das Stativgewinde praktisch aller Kameras
  • Eigener Stativkopf: Statt der Nivellierbasis passt jeder Kopf mit 3/8"-Gewinde auf die Kameraschraube am Schlitten
  • Sony A7 Serie (A7 II, A7 III, A7R IV, A7C, …)
  • Canon EOS 5D Mark III / IV, Canon EOS R, RP, R3, R5, R5 Mark II, R6, R6 Mark II, R7, R8, R10, R50, R100
  • Nikon D810, D850, Nikon Z Serie (Z5, Z6, Z7, Zf, …)
  • Fujifilm X-T3, X-T4, X-T5, X-T30 II, X-T50, X-H1, X-H2, X-H2S
  • Panasonic S Serie (S1, S5, …)
  • Digitales Mittelformat: Fujifilm GFX (getestet mit der GFX 50 bis 3 kg), Hasselblad X1D/X2D
  • Makroobjektive: 50 mm, 60 mm, 90 mm, 100 mm, 105 mm (und vergleichbare)
  • Modulares Zubehör: Film Scanner Holder System, CineStill CS-LITE, Justierspiegel (auch einzeln erhältlich)

Welches Filmformat du scannen kannst, hängt von der Objektivbrennweite ab. Übersicht für Vollformat-Sensoren und Makros bis 1:1, gerechnet mit höchstens 62 cm Abstand zwischen Film und Sensor:

Filmformat Brennweite des Makros
50 mm 60 mm 90 mm 100 mm 105 mm
35mm ja
20,0 cm
ja
24,0 cm
ja
36,0 cm
ja
40,0 cm
ja
42,0 cm
6×4.5 ja
21,6 cm
ja
25,9 cm
ja
38,9 cm
ja
43,2 cm
ja
45,4 cm
6×6 ja
23,8 cm
ja
28,6 cm
ja
42,9 cm
ja
47,6 cm
ja
50,0 cm
6×7 ja
23,8 cm
ja
28,6 cm
ja
42,9 cm
ja
47,6 cm
ja
50,0 cm
6×9 ja
23,8 cm
ja
28,6 cm
ja
42,9 cm
ja
47,6 cm
ja
50,0 cm
4×5 ja
31,1 cm
ja
37,3 cm
ja
55,9 cm
nein
62,1 cm
nein
65,2 cm

ja heißt mindestens 2 cm Reserve, eingeschränkt reicht knapp, nein heißt, der Copy Stand ist zu niedrig. Die Zahl unter dem Urteil ist der Abstand zwischen Film und Sensor, den die Kombination braucht.

Für Micro Four Thirds, APS-C und digitales Mittelformat von Fujifilm und Hasselblad stehen die Tabellen mit Kameranamen auf der Seite Welches Filmformat schafft deine Kamera auf dem Copy Stand?

Lieferumfang

Im Paket Copy Stand + Nivellierbasis Copy Stand + Nivellierbasis + Justierspiegel
Säule: Aluprofil mit Schlitten, Klemmhebel, Kameraschraube 3/8" und Abschlusskappe, fertig montiert ✓ ✓
Grundplatte (Siebdruckplatte, Birke), unten mit zwei Senkungen für die Schrauben ✓ ✓
1× Nivellierbasis mit Adapterschraube 1/4" auf 3/8", Innensechskantschlüssel und Anleitung ✓ ✓
2× Senkkopfschraube M8, 1× Inbusschlüssel 5 mm, 4× Gummifüße zum Aufkleben, Aufbauanleitung (DE/EN) ✓ ✓
1× Justierspiegel, beidseitig mit Schutzfolie – ✓

Technische Details

  • Grundplatte: Siebdruckplatte Birke, 21 mm, 35 × 45 cm (Breite × Tiefe), glatte Seite oben, abgerundete Ecken
  • Profil: Aluminium 30 × 60 mm, Nut 8, 70 cm
  • Verbindung Profil und Platte: 2× Senkkopfschraube M8 von unten direkt ins Profil, die Köpfe liegen bündig
  • Abstand Film bis Kamerasensor: bis rund 62 cm (gerechnet für Filmhalter auf CineStill CS-LITE, mit Nivellierbasis und Schlitten ganz oben; je nach Kamera etwas mehr oder weniger)
  • Schlitten: Technischer Kunststoff, im Profil geführt, Klemmhebel mit Freilauf-Knopf, Daumenmulde, Kameraschraube 3/8"
  • Belastung: getestet mit Fujifilm GFX 50 bis 3 kg für Kamera und Objektiv zusammen; Belastungstest mit 12-kg-Kettlebell am Schlitten
  • Nivellierbasis: Aluminium, 3/8"-Innengewinde, 1/4"-Kameraschraube, Neigung ±15° in jede Richtung, 360° drehbar, Libelle, Traglast 10 kg, Gewicht 230 g
  • Justierspiegel (nur Variante „Copy Stand + Nivellierbasis + Justierspiegel“): Acryl, spiegelbeschichtet, 50 × 50 mm, splittert nicht
  • Standfüße: 4× Gummifüße zum Aufkleben
  • Maße (B × T × H): 35 × 45 × 72 cm
  • Farbe: Platte und Schlitten schwarz, Profil Aluminium
  • Artikelnummer: 1831

Beschreibung

Der Copy Stand ist unser Reproständer für alle, die Negative und Dias mit der eigenen Digitalkamera scannen statt mit einem Flachbettscanner. Die zweite Version haben wir nach einem Jahr Rückmeldungen von euch gebaut, weil viele Großformat wie 4×5 scannen und dafür mehr Platz brauchten.

Welche Kombination zu deinem Setup passt, sagt dir der Film Scanner Finder nach drei Fragen, alle Komponenten im Schichtaufbau zeigt das Sortiment-Diagramm.

Aufbauanleitung

Die einzelnen Schritte stehen in der gedruckten Aufbauanleitung (Deutsch und Englisch) im Paket.

Halte den Schlitten fest, bevor du den Klemmhebel löst, sonst rutscht er mit der Kamera nach unten. Neigung und Klemmung stellst du nach der Anleitung ein, die der Basis beiliegt. Wackelt die Säule, zieh die beiden Schrauben unten mit dem Inbusschlüssel nach. Mit schwerer Kamera ganz oben gibst du dem Aufbau nach dem Verstellen kurz Ruhe oder löst per Selbstauslöser aus.

Häufige Fragen

„Was ist anders als beim bisherigen Copy Stand?“

Grundplatte und Profil sind größer als beim Vorgänger: Die Platte maß vorher 32 × 32 cm bei 15 mm Stärke, das Profil 30 × 30 mm bei 60 cm Länge. Die Kamera sitzt auf einem neuen Schlitten, und die Nivellierbasis gehört jetzt immer dazu.

Anleitung als PDF herunterladen (Deutsch und Englisch)

Vollständige Details anzeigen

Kundenbewertungen

3,5 von 5

Basierend auf 2 Bewertungen100 % verifizierte Bewertungen

Transparenz: Jeder Kunde, der einen bei uns gekauften Artikel bewertet, bekommt unabhängig von der Sternezahl einen Rabattcode für seine nächste Bestellung.

  1. Pär H.Verifiziert

    Copystand review

    Overall a nice piece of equipment. Easily portable .What can be improved?:
    * The screw at the bottom of the aluminum profile connecting with the stand as such is pretty fiddly to work with. I don't use it.
    * The screw connecting to the equipment is pretty hard to work with, especially as the connecting surface does not have any kind of good friction, making any attached equipment rotate easily.
    * Also increase the height of the sliding connector so it does not easily get affected by the weight/momentum of the camera, meaning that it is hard to keep it level.

    Antwort von Ausgeknipst ·

    Thanks Pär, and sorry this sat here without a reply for so long. Your first point is fixed: since September the profile is bolted to the base with an M8 screw instead of the old clamp. For the camera turning on the mount, our levelling base is the fix. It stays screwed to the stand; you turn and tilt the camera on the base itself (360°, up to 15° in any direction) and then lock it. That way the camera no longer turns on the screw, and you can bring the sensor parallel to the film even if the arm gives a little under the camera. The base is available on its own and as a set with the Copy Stand. The slider is designed to be set once per film format rather than adjusted often. If anything still turns or slips, write to info@ausgeknipst.de.
    Vladi · Ausgeknipst

  2. L. P.Verifiziert

    Simple DIY Setup for hobby purposes

    A simply built DIY repro-stand for semi-professional/hobby purposes, but lacking for professional work, the value for its price could be better,

    For a simple Film Scanning setup where height is set once and not adjusted much, it gets the job done. Analogue Repro-work is a bit of a pain with this stand.

    It is generally sturdy, but not smooth and precise enough to call it professional. Setting the height feels very clunky and unstable, tends to shake the construction, unbalancing fine-adjustments each time. Given that setting a specific height is the purpose of a copy stand, this is a minus in value.

    Material quality is generally okay, but lacking in parts. The 3D-printed parts don't move well along the aluminum, and mounting a tripod head is always a pain due to the oversized 3d-printed top of the mounting screw.

    While the relatively small base has the advantage of not taking up much space and still being stable, it doesn't provide enough working surface, depending on tripod-head/-plate used (SmallRig Ballhead in my setup). My Cinestill lightbox and essential film holder sit at the edge of the base. For repro-work I mostly have to extend the surface 'creatively'.

    Came without any assembly instructions, had to guess my way through. For a DIY-Kit like this, the price should definitely be lower.

    Antwort von Ausgeknipst ·

    Thank you for taking the time, this is the most useful review this product has had. Several of your points are already on our list: the sliding block, the friction under the mounting screw and the assembly sheet that should have been in the box in the first place. If you would like to test the improvements, write to info@ausgeknipst.de.
    Vladi · Ausgeknipst

    Update, November 2026: The Copy Stand MK2 is now available and takes up several of your points. The base is 35 × 45 cm instead of 32 × 32 cm, and 21 mm thick. The slider runs guided in the profile, and a thumb rest lets you nudge it a few millimetres. The camera sits on a levelling base that comes with every stand, so you no longer need your own tripod head. Assembly instructions in German and English are in the box. Your review refers to the first version.

Transparenz: Jeder Kunde, der einen bei uns gekauften Artikel bewertet, bekommt unabhängig von der Sternezahl einen Rabattcode für seine nächste Bestellung. „Verifizierter Kauf“ heißt: Die Bewertung kam über den Bewertungslink einer Bestellung in unserem Shop. So sammeln und prüfen wir Bewertungen

Wir sind Anto & Vladi

Junges Startup unterstützen

Du willst innovative Lösungen statt Massenware? Bei uns kaufst du nicht bei einem anonymen Großhändler, sondern direkt bei den Gründern. Wir (Anto & Vladi) haben unser Startup im Oktober 2021 in Würzburg gestartet, um dir dabei zu helfen, die analoge Fotografie wiederzubeleben.

Ausgeknipst Print Room - 3D Drucker Produktionsstaette

Von Ingenieuren entwickelt

Konstruiert in Würzburg

Wir verkaufen nichts, was wir nicht selbst benutzen würden. Wir sind Ingenieure und Kamera-Nerds und wir wissen, dass es besonders bei Kameratechnik auf Präzision ankommt. Deswegen konstruieren wir unsere Teile selbst in Würzburg, die meisten fertigen und montieren wir auch hier. Batterien und Akkus kaufen wir zu, zum Beispiel von Varta.

Ausgeknipst Versand und Lager - Gelbe Lagerkisten

Von Deutschland in die ganze Welt

Schneller DHL Versand

Du willst nicht ewig auf dein Teil warten? Wir packen jede Bestellung in Würzburg und verschicken sie am nächsten Versandtag (Montag, Mittwoch oder Freitag). Innerhalb Deutschlands ist sie danach in 2-4 Tagen bei dir, mit DHL oder der Deutschen Post.